Premium Trolling Motor Mount

The Flux trolling motor mount is a ½-inch thick aluminum plate, powder coated and pre-drilled with tapped holes sized for all major motor brands — including Minn Kota and MotorGuide. No fabrication required. Bolt it on, mount your motor, go fishing.

SKU: SQ0834362 | Price: $275.00

---

What's Included

• 1× powder-coated ½" aluminum mounting plate
• Pre-drilled and tapped holes for Minn Kota and MotorGuide bolt patterns
• Hardware-ready surface — no additional machining needed

---

Why This Trolling Motor Mount Is Built Different

Most mounting plates on the market are either undersized, under-spec'd, or require you to drill your own holes. This one ships ready to install.

½" aluminum construction. That's not a typo. Where competitors use thinner stock, the Flux plate uses half-inch aluminum throughout — the same material spec used in structural marine fabrication. It doesn't flex under load, and it doesn't corrode in saltwater.

Powder coat finish. The coating isn't cosmetic. It's a functional barrier against the oxidation that kills bare aluminum in brackish or saltwater environments, making this a proper saltwater trolling motor mount for anglers running coastal, inshore, or offshore.

Pre-drilled and tapped. The bolt pattern is machined in — not drilled with a hand drill at assembly. Whether you're running a Minn Kota mounting plate setup or need a MotorGuide mounting plate configuration, the holes are already there.

Fits multiple boat sizes. The plate geometry is designed to span a range of hull widths, so it works on aluminum jon boats, fiberglass bass boats, and center console builds alike. If you need a trolling motor mount for center console rigging, this plate handles that without modification.

---

Specs

| Spec | Detail | |---|---| | Material | 6061 Aluminum | | Thickness | ½ inch (0.500") | | Finish | Powder coat | | Hole Pattern | Pre-drilled & tapped for Minn Kota and MotorGuide | | Application | Bow mount, transom, center console | | Saltwater rated | Yes |

---

How Does It Compare to Other Aluminum Trolling Motor Plates?

Other custom trolling motor mount options on the market typically fall into two categories: thin stamped plates with no tapped holes, or fully custom weld-up brackets that run $400–$600 and require a lead time. The Flux plate sits in neither camp.

It's machined from ½" aluminum stock — heavier and more rigid than the lighter-gauge plates offered by most catalog suppliers — and it ships with the work already done. The tapped holes mean you're threading into metal, not a washer-and-nut sandwich that loosens over a season.

For anyone who's dealt with a bow mount trolling motor plate walking loose mid-day on rough water, that detail matters.

---

Frequently Asked Questions

What trolling motor brands does this mount fit?

The plate comes pre-drilled and tapped for Minn Kota and MotorGuide bolt patterns — the two dominant brands in the market. If you're running a different brand, contact us before ordering to confirm compatibility.

Is this mount suitable for saltwater use?

Yes. The powder coat finish protects the aluminum against corrosion in saltwater and brackish environments. It's designed explicitly as a saltwater trolling motor mount for anglers fishing coastal or inshore applications. For additional corrosion protection on hardware, use 316 stainless fasteners — see ABYC guidelines on marine hardware corrosion.

Can I use this as a trolling motor mount for a center console?

Yes. The plate dimensions accommodate center console gunwale and deck mounting configurations. It's one of the more common use cases we see for this plate.

How thick is the aluminum compared to standard mounting plates?

At ½ inch, it's thicker than the majority of off-the-shelf plates. Most catalog aluminum trolling motor mounting plates run 3/16" to ¼". The extra material adds rigidity and load capacity — relevant when you're pushing a 55 lb or 80 lb thrust motor at speed. Aluminum alloy 6061 mechanical properties confirm why it's the standard for structural marine components.

How is the mounting plate installed?

Drop it into position on your bow deck or transom surface, align to your existing hull mounting points, and thread your motor's hardware directly into the tapped holes. No welding, no secondary drilling.

Does this replace a transom bracket?

This is a mounting plate, not a transom bracket. It provides a rigid flat surface to seat your motor's foot bracket. If you need a dedicated transom bracket solution, see our page.

---

Related Products

---

Built by Flux. Questions? Contact our team before you order — we'll confirm fitment for your specific hull and motor.